Fabrication of Alkaline-Earth Fluoride Ceramics for High-Power Lasers via Fusion Casting and Hot Forging
2023
- 61Usage
Metric Options: CountsSelecting the 1-year or 3-year option will change the metrics count to percentiles, illustrating how an article or review compares to other articles or reviews within the selected time period in the same journal. Selecting the 1-year option compares the metrics against other articles/reviews that were also published in the same calendar year. Selecting the 3-year option compares the metrics against other articles/reviews that were also published in the same calendar year plus the two years prior.
Example: if you select the 1-year option for an article published in 2019 and a metric category shows 90%, that means that the article or review is performing better than 90% of the other articles/reviews published in that journal in 2019. If you select the 3-year option for the same article published in 2019 and the metric category shows 90%, that means that the article or review is performing better than 90% of the other articles/reviews published in that journal in 2019, 2018 and 2017.
Citation Benchmarking is provided by Scopus and SciVal and is different from the metrics context provided by PlumX Metrics.
Example: if you select the 1-year option for an article published in 2019 and a metric category shows 90%, that means that the article or review is performing better than 90% of the other articles/reviews published in that journal in 2019. If you select the 3-year option for the same article published in 2019 and the metric category shows 90%, that means that the article or review is performing better than 90% of the other articles/reviews published in that journal in 2019, 2018 and 2017.
Citation Benchmarking is provided by Scopus and SciVal and is different from the metrics context provided by PlumX Metrics.
Metrics Details
- Usage61
- Abstract Views52
- Downloads9
Thesis / Dissertation Description
Cubic alkaline-earth fluorides, specifically CaF2 and SrF2, have long been recognized as good laser host candidate materials for high-power amplifiers. Their low linear and nonlinear refractive indices, negative thermo-optic coefficient, high thermal conductivity, low intrinsic optical loss over a broadband spectrum and ability to incorporate rare-earth ions with low quantum defects are just a few of their attractive properties. Traditionally grown from the melt up to foot-size dimensions, these materials can also be advantageously prepared in the form of transparent ceramics to improve on gain uniformity by eliminating dopant segregation and stress-induced birefringence. Transparent ceramic gain media offer additional benefits in terms of enhanced thermal shock resistance due to their fine microstructure and process scalability. The fabrication of transparent ceramics with controlled microstructures is usually achieved by sintering fine powders below their melting point. However, due to the high surface area of these powders, oxide contamination can lead to scattering loss in the sintered parts. In an attempt to circumvent this limitation, this work investigates the fabrication of transparent ceramics by fusion casting and their ceramization via hot forging. Specifically, we have evaluated the processing conditions for fusion casting of Nd:SrF2 and shown how reducing the cooling rate from 25°C/hr to 1.5°C/hr can increase optical transmission up to the Fresnel limit in the near-IR. Similarly, we have delineated the conditions under which a randomized microstructure can be obtained by uniaxial deformation of CaF2 single crystals and Nd:SrF2 fusion cast ceramics, yielding a 30% increase in fracture toughness from 1.7 to 2.2 MPa*m1/2 for CaF2. While further optimization can still be achieved, our best samples exhibit inline scattering losses of 0.002 cm-1 at 1.5 μm compared to 0.25 cm-1 at 1.06 μm for ceramics fabricated via hot-pressing. This two-step approach has the potential to provide a cost-effective pathway to large, low-loss alkaline-earth fluoride laser gain media.
Bibliographic Details
Provide Feedback
Have ideas for a new metric? Would you like to see something else here?Let us know